NEWS
- » Maintenance - Repair of screw air compressors
- » Repair of Piston air compressors
- » Repair of air dryers
- » Replacement of compressed air filter elements
- » Lease of air compressors
- » Repair of chillers
- » Maintenance - Repair of Vacuum Pump
- » Maintenance - Repair of air blowers
- » Knowledge of lube oil for air compressors
- » Design - Execution - Installation of compressed air system
Guidelines for inspection of Handsome II
Guidelines for inspection of Handsome II
Inspection intervals and inspection items depend on the installation site as well as operating conditions. The table below provides the rough guidlines. Sound operation is expected if the guidelines are followed.
Parts | Inspection items. | Daily | Semi-annually ( every 3000h) |
Annually ( every 6000h) |
Every 2 years (12000h) |
Overhaul every 4 years | Remarks |
Dust filte | Check and leaning | * |
Cleaning interval depends on the operating conditions /
|
||||
Suction filter | Check for contamination or cleaning . | * |
The severity of contamination and clogging differs according to the operation conditions. Change suction filter if badly contaminated. |
||||
Oil filter cartridge | Check and cleaning . | (0) |
Check the fitting part. If improperly fit, replace the cartrige. |
||||
Oil separator element. | Regular change. | (0) |
Change element when changing lubricating oil.
|
||||
Compressor machnical seal. | Check. | * | (0) |
|
|||
Change. | (0) |
|
|||||
Bearing for compressor. | Check and cleaning. | * |
Change silencer if badly contaminated. |
||||
Oil cooler After cooler /Bộ làm mát dâu. |
Check on fin for dirtiness and cleaning | * |
Increase or decrease the cleaning frequency depends on the operating conditions |
||||
Dryer condenser | Check and cleaning | * |
Clean condenser together with cooler |
||||
Poly V-belt | Check or retension | * |
Check V-belt for tension, wear, damage, crack and slipping. |
||||
Change | (0) |
Change V-belt every four years or 12000h whichever comes earlier |
|||||
Volumetric regulating valve diaphragm | Functional check and change | * |
Replace in case of malfuntion |
||||
Presure control valve | * | ||||||
Solenoid valve | Funtional check. | ||||||
Safety valve | |||||||
Dryer solenoid valve ( for dryer intergrated types) | * |
Clean or change in case of malfuntion |
|||||
Drain separator( For unit w/o dryer) | * |
Clean or change in case of malfuntion |
|||||
Main motor | Insulation test | * |
Motor is usable if resistance is 10 Ω or more when cooled. |
||||
Bearing change | * | (0) |
|
||||
Starting board(Magnets, relays, wiring, etc.) | Funtional check |
|
|||||
Sensor | Funtional check |
Replace with new one in case of malfuntion |
|||||
Oil gauge | Funtional check | * |
Make sure the oil level is within the range between the upper limit and the lower limit. If it’s below the lower limit, replenish lubricant. The oil level falls by approx 30mm when 24 operation is continued for one month |
||||
Lubricating oil | Regular change | (0) |
|
||||
Lubricating oil | Regular change | (0) |
As a guideline, change every two years or 3000h |
- Change parts marked with * when defects or errors are observed
- Change parts marked with (0 )
- Warranty period of this machine shall be 12 months from the date of completion of the test run 15 months from the maintenance are of shipment, whichever comes earlier.
- Standards for listed based on normally expected practices.
Overhaul the machine every 4 years, regardless of operation hours. At the same time, change bearings and clean the coil of the motor.
Minh Phu provides maintenance and repair services for air compressors, in addition Minh Phu also provides spare parts for air compressors with high quality at reasonable prices. For further information, please contact (+84)919 23 28 26. Sincerely thank you for your interest and your trust of our service.

Newer articles
Older articles