Technology

Swan air compresssor TS series

Swan air compressors TS series are designed to be compact and dedicated, highly durable, imported air end from Europe, fully-sealed motors, modularized air inlet system,user-friendly equipment panel easy to use.
Process of technical safety audition of pressure

Process of technical safety audition of pressure

The process of technical safety inspection on average is subject to the pressure of QA: 09 - 2014 / BLDTBXH
Air end repairs

Air end repairs

After air end diagnostics, our engineers estimate the necessary repairs and provide calculation of the repairs and necessary spare parts
Piston air compressor

Piston air compressor

Cung cấp, sửa chữa máy nén khí Piston

Maintenance of Handsome II air compressor

Compressed air system in factory plays an important role. In order to ensure the stable operation during the manufacturing process, the regulary maintenance is nescessary . However, there are many different problems in fact such as: Air compressors, dusty air dryers, high engine room temperatures, unsecured wind convection ... lead to reduce using time of compressor accessories (air filter, oil filter, oil separator ...). On the other hand, the recommended maintenance in some factories is not seriously followed and there are deviations.

Part list of Handsome II air compressor

Wednesday - 31/07/2019 22:20

When ordering parts, specify the machine type , part name, part numbers to our authorized distributor. Use Kobelco Handsome II genuine parts when replacing worn parts or repairing. Using non-genuine parts does not guarantee proper functions and may result in a failure.

Parts  Parts number HM37A HM37AD
Dust filter Left side face P-CE05-521 2 2
Right sude face P-CE05-554 2 5
Suction filter element S-CE05-503 1 1
Oil filter cartridge P-CE13-520 1 1
Volumetric regulating valve diaphragm. 4J11V01001P1 1 1
Presure keeping check valve. P-FC12-527 1 1
Solenoide valve. 0,69 MPa P-FC81-624 1 1
0,83 MPa P-FC81-598#01 1 1
Oil separator element.
 
P-CE03-572 1 1
Temperature control valve. P-FC61-502#03 2 2
Safety valve. 0,69 MPa P-FC21-535#01 1 1
0,83 MPa P-FC21-535#02 1 1
Pressure control valve. P-V31-003 1 1
Discharge temperature sensor. P-EA01-571#03 1 1
Oil recovery check valve. 4F04V01008F1 1 1
Silencer. P-CD01-510 1 1
Mechanical seal. P-GA05-521 1 1
Pressure switch 0,69 MPa P-EA02-566#05 1 1
0,83 MPa P-EA02-566#04 1 1
Poly V-belt 50 Hz P-AE24-596#09 1 1
60 Hz P-AE24-596#07 1 1
Drain separator P-FC41-501 1 -
Parts  Parts number HM37A HM37AD
Dust filter Left side face P-CE05-521 2 2
Right sude face P-CE05-554 2 5
Suction filter element S-CE05-503 1 1
Oil filter cartridge P-CE13-520 1 1
Volumetric regulating valve diaphragm. 4J11V01001P1 1 1
Presure keeping check valve. P-FC12-527 1 1
Solenoide valve. 0,69 MPa P-FC81-624 1 1
0,83 MPa P-FC81-598#01 1 1
Oil separator element.
 
P-CE03-572 1 1
Temperature control valve. P-FC61-502#03 2 2
Safety valve. 0,69 MPa P-FC21-535#01 1 1
0,83 MPa P-FC21-535#02 1 1
Pressure control valve. P-V31-003 1 1
Discharge temperature sensor. P-EA01-571#03 1 1
Oil recovery check valve. 4F04V01008F1 1 1
Silencer. P-CD01-510 1 1
Mechanical seal. P-GA05-521 1 1
Pressure switch 0,69 MPa P-EA02-566#05 1 1
0,83 MPa P-EA02-566#04 1 1
Poly V-belt 50 Hz P-AE24-596#09 1 1
60 Hz P-AE24-596#07 1 1
Drain separator P-FC41-501 1 -
           

                                 *Smaller parts such as packing and O-rings that are to be changed along with major parts are omitted.

8.3 Adjustment of  Poly V-belt and Pulleys.

  • Adjusting tension of poly V-belt

Measure the tension of the poly V-belt using a frequency measuring instrument. Be sure to adjust the tension  to the specified value. Excessive tension may cause belt rotor shaft or reduction in bearing life, whereas insufficient tension may cause belt slipping. Adjust frequency with adjusting bolts using a frequency measuring instrument.
Frequency adjustment using frequency measuring instrument.

                                 

 

Frequency of power supply.

50 Hz

60 Hz

STD (0,69 Mpa {7,0 kgf/cm2}

102Hz

98Hz

H (0,69 Mpa {8,5 kgf/cm2}

100Hz

96Hz

 

  • Aligning pulleys

Fit a ruler at the ends of large and small pulleys, and make sure that the clearance between them is 1.0 mm or less.
 

Total notes of this article: 0 in 0 rating

Click on stars to rate this article