Technology

Air compressor oil uses

Air compressor oil uses

The movement of screw is pineaple-sharpened, therefore it's nescessary to use lubricating oil with theaim to reduce the corrosion and softly operate. The bearing is completely stay in air end so it is also lubricated with air compressor oil.

Precaution before operation of Handsome II air compressor

Precaution before operation of Handsome II air compressor

Swan TS-V air compressor

Swan TS-V airr compressor series is a series of machines using inverter to reduce power consumption and have outstanding features of the Swan TS series. Based on operating phenomena to optimize operation, ensure maximum air volume and minimum power consumption, average electricity savings at: 15% - 30%. Protection and advanced control system improved reliability of safe and enhanced operating performance; Air compressor starts at zero speed, extending the machine's durability.
How to maintain air dryer?

How to maintain air dryer?

Bảo dưỡng máy sấy khí như thế nào? Kiểm tra xe ống thoát khí, thoát nước hình chữ U có thoát khí nén và nước cứng bình thường không. Hãy dọn dẹp một tháng hơn một lần ống thoát hình chữ U. Kiểm tra xem có bộ phận nối ống nào bị rò rỉ không. Hãy duy trì cách ổn định nhiệt độ bên trong ( dưới 38oC) và nhiệt độ cửa vào khí nén ( dưới 38oC). Đồng thời phải dọn dẹp theo chu kì để bụi, tạp chất không phủ lên tụ điện của bộ làm mát sau và máy sấy khí ( cách khoảng 1-2 tuần)

Instruction for operation of Handsome II air compressor

Instruction for operation of Handsome II air compressor

 Schedule Operation of GRH3 air compressor

Monday - 29/07/2019 05:13
 Schedule Operation
1. Check and enter the schedule operation time.
           For the directions, refer to page 49
 
2. If selecting Schedule mode by pressing Schedule operation mode button once, the following screen is displayed.

                                 
3. If pressing START button, it shows the following screen and the compressor operates and stops in accordance with the schedule operation time.
 
                      
Schedule operation stand-by screen.

During schedule operation: the screen is displayed when the compressor is stand-by before the
schedule operation time.

Schedule operation screen. 
During schedule operation: if the compressor operates at the time of schedule operation, the left
screen is displayed. When the main motor rotates by schedule operation, mark blinks.

  2. Remote Operation.
It is basically structured so that the remote operation, stop control and operation status are outputted to the contact. Just attach the Start and Stop buttons as presented in the below figure.
  1. Remote Operation .                                                 
    It operates if turning on No.10terminal(105) and  No.12 terminal(+24) once.
  2. Remote Stop
                        It stops if turning on No.11 terminal(106) and  No.12 terminal(+24) once.
  1. On contact during operation.
                During operation, No.18 terminal(111)  and  No.19 terminal(112) are on
  1. On contact if any abnormal status.
               If any trouble occurs, No.20 terminal(113) and No.21 terminal(114)   are   on.
                     5. Remote manual no-load instruction.
              If No.04 terminal(+24) and No.09 terminal(104) are on, it operates under  no load and when   they are off, its pressure is                      automatically controlled.
 3. Remote Monitoring System [Micom]
When it is necessary to remotely monitor compressor operation, stop and operation status, using [Remote Monitoring Control System] may facilitate the management of the compressor. It is structured as follows.
<Specifications>


Dimensions: 320(W) x 270(H) x 120(D)

Power Supply : AC220V Single Phase 50VA

Connection Control Cable : UTP Lan Cable 1 cable

Every situation displayed on the compressor Micom such as compressor operation temperature, discharge pressure, filter use time and troubles is displayed on the remote monitoring system(remote controller).

Remote monitoring System [Computer]
When remotely monitoring compressor operation, stop control and operation status, using [Remote Monitoring Control System] may facilitate the control of the compressor, it is structured as follows.
Components: computer, COM card[computer], COM cable
No. of controlled sets: 8.


 


 

Total notes of this article: 0 in 0 rating

Click on stars to rate this article