- » Maintenance - Repair of screw air compressors
- » Repair of Piston air compressors
- » Repair of air dryers
- » Replacement of compressed air filter elements
- » Lease of air compressors
- » Repair of chillers
- » Maintenance - Repair of Vacuum Pump
- » Maintenance - Repair of air blowers
- » Knowledge of lube oil for air compressors
- » Design - Execution - Installation of compressed air system
Some common faults of inverter- air compressor using inverter.
Some common faults of inverter- air compressor using inverter.
Nowaday, there are many different types of inverters and diffent firms has various types depending on the needs from simple to complex, more and more perfect and improved they are . These inverters may vary in structure and component details but the principle is almost the same.
Whatever inverter is using most ICs combined with transistors, voltage stabilizer, capacitors and various componients such as resistors, pulse transformers ...
The dynamic circuit must have thyristors, transistors and power diodes ... to make direct inverter or indirect inverter.
Here are some common failures in a specific inverter (Japanese production) using 3-phase 3 * 220V, 3A power. MIKI PULLEY'symbolized l VM1- 04-2, from here can reduce the problem in another inverter.
a. Failure of control circuit
The source region is the most damaged place because most of the ICs as well as other active components are very sensitive to the fluctuations of electricity, the wet and dust environment; abnormal increase or decrease of the power supply, high temperatures, chemically contaminated air, or near the sea causing damage to internal components
Connect the power, turn on the switch for starting the inverter , but the motor supplied powerfrom the inverter does not work. the LED do not light up. If measuring the output voltage at 3 phases U, V W indicates 0 but the power still enough to supply 3-phase power on R, S,T, definitely the source is failed. Then keep checking, the fuse does not break, the voltage is remained after the transformering, it mean the rectifier bridge, diodes or filter resistors are broken. The power switch is turned on but the fuse is immediately broken that means the cause of the problem may be: AC transformer is broken;lines cooled; filter capacitor risk; short- circuited rectifier .. The failures are arranged in following order:+ Primary or secondary coil is short circuit.
+ The parasitic filter capacitors, leaked one-way filter capacitors, short circuit.
+ Explosion of stabilizing diodes.
+ The rectifier diodes are broken Finally, check the resistors, capacitors, ceramic capacitors. Particularly, transistor and IC have little damage and if it is damaged, it'll be definitely difficult to detect and require experience to find out.
-The source,the LED is still good, but the device cannot run or work improperly, the damage usually occurs in the inverter. Measuring One-way voltage; checking whether the VR potentiometer (to adjust one-way U into the circuit) broken or worn out?
Control system consists of synchronous transformers, AC voltage regulator circuit and filter circuits; active components such as IC algorithms for comparison:
Digital ICs for control circuits; Non-synchronous control circuit requires quite complex techniques; There are many specially tuned cores which have been manufactured by the experts specialized in measuring devices with high accuracy to ensure the symmetry of control edge a for all channels. You had better not twrist , adjust these components. The best way is to clean it, use compressed air to blow away all dirt from the printed circuit and components. Use a hair dryer to blow heated air into moistured areas. Tighten the screws at the connection points, firmly tighten the plugs, weld the cracked components if nescessary. The machine works well after using some simple tips above. Nomally, the components in the control circuit are less damaged as in the dynamic circuits.
b. Failure of dynamic circuit
Control circuit is still good; Turn on the switch: The Power-RUN light is still light up, but after a few seconds the inverter gradually heats up, the circuit automatically cuts off the power, the LED turns off. The main reason is due to short-circuit. Check the printed circuit from the three-phase source R, S, T to the A-K poles of thyristors, power diodes if there is any touch, cool touch? Check if there is any lines on the printed circuit that peels off, spits out or scorched marks
Cut off the power, touch each thyristor, diode, if you encounter any hotter led than all of those, that's position where the problem happened. Using welding torch to remove damaged components from the printed circuit to check with multimeter, replace new components with the same code if damaged,
Check the lines from the K pole to the wiring board, on the printed circuit that leads to U, V, W, must check all the components on the circuit related to the K pole of this broken thyristo, connect the inverter to work again, it everything's fine. Measure voltage values at standard points and compare with inverter of the same type.
Minh Phu provides maintenance and repair services for air compressors, in addition Minh Phu also provides spare parts for air compressors with high quality at reasonable prices. For further information, please contact (+84)919 23 28 26. Sincerely thank you for your interest and your trust of our service.

Newer articles
Older articles