Technology

Common causes and troubles of vacuum pump

Common causes and troubles of vacuum pump

During operation as well as operation of operators '"Malfunction is unavoidable'" Some basic incidents such as: Do not reach vacuum level, pump overload ... With many years of experience, We have successfully repaired many vacuum pumps. The following are some of the reasons why the vacuum pump failures, and some common vulnerabilities with the hope that the operator can identify and take prevention.
Maintenance compressed air system

Maintenance compressed air system

The maintenance compressed air systems are often specified in the system documentation, provided by the manufacturer. In this artical we would like to introduce some rules and maintenance regimes according to general regulation.
Compressors equipment repairs

Compressors equipment repairs

Screw air compressors are in the important position in the industrial process, therefore all aggregates break and troubleshooting affect to industrial process in general and have not expected results. Screw air compressors quality and advantages are undeniable, but every mechanism is run-out eventually, some parts do not operate stably, some are out of operation.

Operation control of GRH3 air compressor

Operation control of GRH3 air compressor

Guide of air filter maintenance

Compressed air system in factory plays an important role. In order to ensure the stable operation during the manufacturing process, the regulary maintenance is nescessary . However, there are many different problems in fact such as: Air compressors, dusty air dryers, high engine room temperatures, unsecured wind convection ... lead to reduce using time of compressor accessories (air filter, oil filter, oil separator ...). On the other hand, the recommended maintenance in some factories is not seriously followed and there are deviations. To extend the life of the machine as well as compressor components and ensure operator safety Air compressors are very important to maintain regularly and technically correct.Air compressors, dusty air dryers, high engine room temperatures, unsecured wind convection ... lead to reduced use time of compressor accessories (air filter, loc oil, oil separator ...). On the other hand, the maintenance (maintenance) recommended by the manufacturer in some factories is not guaranteed and there are deviated. To lengthen longevity of mạchine as well as compressor components and ensure operator safety , air compressors are very important to maintain regularly and technically .

The special cases of 3-phase asynchronous motors

Wednesday - 02/01/2019 03:39

The special symptoms of 3-phase asynchronous motors

dong co dien 1 pha,3-phase asynchronous motors
3-phase asynchronous motors

The unloading condition of the motor is  normal,  in this artcle some special cases are mentioned:

1. Unloading motor

Unload motor (spin without load) or very  weak load, weak currents in the motor that do not harm the engine, but waste resource, and low  capacity  factor and output, causing waste electrical energy . Therefore,  the motor had not better to be  worked  under load or unload .

2. Short-circuited case 

Short-circuited phenomena can be caused by: 

The insulating resistor of the motor is reduced (due to the damped engine) or due to a mechanical collision that damages the insulation, causing a short circuit among the phases, or the wires of a phase. , or phases. Also please note the following symptoms:

When you turn on, rotor can not spin, curent on the windings is very high , if  this symptoms is ignored in long time, motor will be broken. This is called short-circuited phenomena
Before operating motor, you should measure insulating resistor. To small or medium capacity motor, if insulating resistor is less than 0,5 M, you have to dry motor before operation. While operating , if motor is clogged or the load is too heavy, immediately disconnect power( if not the motor will be burnt).  

3. Working case with asymmetric voltage 

If the 3-phase voltage is installed in an unbalanced motor, in the motor outside the magnetic field (in the same direction as the rotor rotation), or in inverse magnetic field. The magnetic field that causes an inverse  torque to rotation direction reducing  the torque  motor, increasing the loss, electric currents   and the heat of motor. The working condition of asymmetric voltages that often occurs in production is the loss of an electric phase. If this situation is not corrected for a long time, the motor will be  burnt.

 

Minh Phu provides maintenance and repair services for air compressors, in addition Minh Phu also provides spare parts for air compressors with high quality at reasonable prices. For further information, please contact (+84)919 23 28 26. Sincerely thank you for your interest and your trust of our service. The special symptoms of 3-phase asynchronous motor

Total notes of this article: 0 in 0 rating

Click on stars to rate this article